Journal of Science and Technology of Composites

Browse Keyword Index

A B C D E F G H I J K L M N O P Q R S T U V W X Y Z ALL

A

  • A356 Al Fabrication and investigation of microstructutr and mechanical properties of A356-TiO2-Gr surface Hybrid nano composite by friction stir processing [Volume 5, Issue 1, 2018, Pages 61-68]
  • ABAQUS Three dimensional modeling of progressive damage in fiber reinforced materials base on invariant failure criteria [Volume 5, Issue 2, 2018, Pages 191-199]
  • Accumulative roll bonding (ARB) A Study of layer strength in composite Al 1050/SS 316 manufactured by Accumulative Roll bonding process [Volume 5, Issue 4, 2018, Pages 479-484]
  • Acoustic emission Failure mechanisms in open-hole laminated composites under tensile loading using acoustic emission [Volume 5, Issue 1, 2018, Pages 143-152]
  • Adhesive The Effects of Temperature Level and Stress-to-Strength Ratio on Creep Behavior of Aluminum-Aluminum Single Lap Adhesive Joints [Volume 5, Issue 3, 2018, Pages 353-358]
  • Alumina granule Compression and impact strength study of aluminum-alumina granule composite by squeez-casting method [Volume 5, Issue 3, 2018, Pages 387-394]
  • Aluminium Compression and impact strength study of aluminum-alumina granule composite by squeez-casting method [Volume 5, Issue 3, 2018, Pages 387-394]
  • Aluminum foam sandwich Response of aluminum foam sandwiches under low rate impact [Volume 5, Issue 2, 2018, Pages 177-184]
  • Amorphous-nanocrystalline coatings The comparison in corrosion behavior of Fe-Ni-Cr composite coatings reinforced by SiC nanoparticles and carbon nanotubes [Volume 5, Issue 3, 2018, Pages 369-376]
  • Artificial neural networks Utilization of artificial neural networks for detection and classification of damages in composite plate-like structures via ultrasonic guided waves [Volume 5, Issue 3, 2018, Pages 343-352]

B

  • Ballistic Limit Velocity Experimental and numerical investigation of high velocity impact resistance in fiber metal laminates [Volume 5, Issue 1, 2018, Pages 99-108]
  • Ballistic Limit Velocity Numerical investigation of the effect of material strain rate dependent properties on high velocity impact behavior and ballistic limit velocity of honeycomb structures [Volume 5, Issue 4, 2018, Pages 511-520]
  • Basalt fibers Effect of Surface Modification of Graphene Nanoplatelets on the High Velocity Impact Behavior of Basalt Fibers Reinforced Polymer-Based Composites [Volume 5, Issue 1, 2018, Pages 109-116]
  • Basalt fibers Effects of functionalized graphene nanoplatelets on the flexural behaviors of basalt fibers/epoxy composites [Volume 5, Issue 3, 2018, Pages 315-324]
  • Batch foam Investigation of cell wall thickness and impact strength of polypropylene microcellular nanocomposite foams produced by batch process [Volume 5, Issue 1, 2018, Pages 135-142]
  • Bending Tensile and flexural properties of epoxy-date palm fiber composites [Volume 5, Issue 1, 2018, Pages 69-78]
  • Bubble growth Experimental Investigation on the Foaming Dynamics and Cell Microstructure of Polystyrene/Nanosilica/n-Pentane Nanocomposites [Volume 5, Issue 2, 2018, Pages 289-301]
  • Buckling Prediction of the critical buckling load of composite cylindrical shells by using Vibration Correlation Technique [Volume 5, Issue 3, 2018, Pages 359-368]
  • Buckling Buckling analysis of composite cross-ply laminated plates under hygrothermal loads with delaminations using the finite strip method [Volume 5, Issue 3, 2018, Pages 437-450]

C

  • Carbon Epoxy An investigation on the static buckling behavior of laminated cylindrical composite shells with embedded SMA wires by experiment [Volume 5, Issue 4, 2018, Pages 551-564]
  • Carbon fiber reinforced composite Statistical study of the effect of various machining parameters on delamination in drilling of carbon fiber reinforced composites [Volume 5, Issue 1, 2018, Pages 41-50]
  • Carbon Nanotube Micromechanical analysis of electro-elastic response of polymer composites reinforced with fuzzy fiber containing CNTs [Volume 5, Issue 4, 2018, Pages 485-498]
  • Carbon nanotube/Cadmium Oxide Production of uniform nanocomposite coating of polypyrrole carbon nanotube/ cadmium oxide to protect corrosion of austenitic stainless steel 304 [Volume 5, Issue 3, 2018, Pages 377-386]
  • CARB process Evaluation of mechanical properties and microstructure for Al/Ni %5 produced by cross accumulative roll bonding process [Volume 5, Issue 2, 2018, Pages 279-288]
  • Casting nanocomposite Investigation of the microstructure and hardness of cast Al7068 nanocomposite reinforced with SiC nanoparticles [Volume 5, Issue 4, 2018, Pages 461-468]
  • Cell density Experimental Investigation on the Foaming Dynamics and Cell Microstructure of Polystyrene/Nanosilica/n-Pentane Nanocomposites [Volume 5, Issue 2, 2018, Pages 289-301]
  • Cell wall thickness Investigation of cell wall thickness and impact strength of polypropylene microcellular nanocomposite foams produced by batch process [Volume 5, Issue 1, 2018, Pages 135-142]
  • Charpy impact An Experimental investigation on nitinol shape memory alloy reinforced GLAREs against Charpy low velocity impact [Volume 5, Issue 3, 2018, Pages 403-414]
  • Circular plate Hydroelastic vibration analysis of functionally graded circular plate in contact with bounded fluid by Ritz method [Volume 5, Issue 4, 2018, Pages 529-538]
  • Coating Preparation of SiO2/TiO2 ceramic nano composite coating by sol-gel method on carbon steel and study the properties of it against corrosive ion in treated wastewater [Volume 5, Issue 1, 2018, Pages 33-40]
  • Composite Investigation of skin/core debonding effects on the natural frequencies of composite sandwich structures using experimental and numerical modal analysis [Volume 5, Issue 1, 2018, Pages 91-98]
  • Composite A semi-empirical model to predict the low-velocity impact behavior of weft-knitted spacer fabrics reinforced composites [Volume 5, Issue 1, 2018, Pages 117-126]
  • Composite Failure mechanisms in open-hole laminated composites under tensile loading using acoustic emission [Volume 5, Issue 1, 2018, Pages 143-152]
  • Composite Compression and impact strength study of aluminum-alumina granule composite by squeez-casting method [Volume 5, Issue 3, 2018, Pages 387-394]
  • Composite Effect of Nitinol Addition on the Mechanical properties and the Microstructure of Nactural Hydroxyapatite Obtained from Calf Femoral Bone [Volume 5, Issue 2, 2018, Pages 238-244]
  • Composite Al/St A Study of layer strength in composite Al 1050/SS 316 manufactured by Accumulative Roll bonding process [Volume 5, Issue 4, 2018, Pages 479-484]
  • Composite beam Evaluation of variation in the mechanical properties of composite laminates using progressive failure analysis [Volume 5, Issue 1, 2018, Pages 51-60]
  • Composite beam Energy Harvesting from Laminated Composite Beam with a Piezoelectric Layer under Forced Vibrations [Volume 5, Issue 2, 2018, Pages 227-237]
  • Composite coatings The comparison in corrosion behavior of Fe-Ni-Cr composite coatings reinforced by SiC nanoparticles and carbon nanotubes [Volume 5, Issue 3, 2018, Pages 369-376]
  • Composite cylindrical shells Prediction of the critical buckling load of composite cylindrical shells by using Vibration Correlation Technique [Volume 5, Issue 3, 2018, Pages 359-368]
  • Composite materials The effect of middle layer material and thickness on the quasi-static energy absorption of FML [Volume 5, Issue 3, 2018, Pages 427-436]
  • Composite plates Finite element simulation of high velocity impact on polymer composite plates [Volume 5, Issue 2, 2018, Pages 157-168]
  • Composite plates Ultimate strength analysis of imperfect composite plates under both in-plane compressive load and lateral pressure using Ritz method [Volume 5, Issue 1, 2018, Pages 1-10]
  • Composite plates Utilization of artificial neural networks for detection and classification of damages in composite plate-like structures via ultrasonic guided waves [Volume 5, Issue 3, 2018, Pages 343-352]
  • Composite plates Buckling analysis of composite cross-ply laminated plates under hygrothermal loads with delaminations using the finite strip method [Volume 5, Issue 3, 2018, Pages 437-450]
  • Composites made with tubular braiding Prediction and control of the mechanical properties of braided composite by controlling the braid angle using the micro-mechanical relationships for each of the flat faces of mandrel [Volume 5, Issue 4, 2018, Pages 595-604]
  • Composite tube Experimental and Finite Element Investigation of Hot Gas Forming Process of A6063-AZ80 Bi-layered Composite Tubes using Taguchi Methods for Design of Experiments [Volume 5, Issue 1, 2018, Pages 79-90]
  • Composite tubes Experimental Investigation of the Effect of Different Parameters on the Behavior of Glass / Epoxy Composite Tubes under quasi-Static axial Loading [Volume 5, Issue 4, 2018, Pages 499-510]
  • Computed tomography Response of aluminum foam sandwiches under low rate impact [Volume 5, Issue 2, 2018, Pages 177-184]
  • Contact non-linear equation Analytical modeling to predict dynamic response of Fiber-Metal Laminated Panel subjected to low velocity impact [Volume 5, Issue 3, 2018, Pages 331-342]
  • Corrosion The comparison in corrosion behavior of Fe-Ni-Cr composite coatings reinforced by SiC nanoparticles and carbon nanotubes [Volume 5, Issue 3, 2018, Pages 369-376]
  • Corrosion Protection Preparation of SiO2/TiO2 ceramic nano composite coating by sol-gel method on carbon steel and study the properties of it against corrosive ion in treated wastewater [Volume 5, Issue 1, 2018, Pages 33-40]
  • Creep The Effects of Temperature Level and Stress-to-Strength Ratio on Creep Behavior of Aluminum-Aluminum Single Lap Adhesive Joints [Volume 5, Issue 3, 2018, Pages 353-358]
  • CTBN Effect of CTBN liquid rubber and flexible diamine curing agent on epoxy/glass prepregs properties [Volume 5, Issue 1, 2018, Pages 25-32]
  • Curing kinetic Curing kinetic of micro and nano composites based on styrenine butadiene rubber contains zinc oxide [Volume 5, Issue 2, 2018, Pages 253-264]
  • Cylindrical lattice Experimental and numerical investigation on semi-cylindrical compositelatticereinforced with triangular cellssubjected to high velocity impact [Volume 5, Issue 2, 2018, Pages 208-217]
  • Cylindrical Shells An investigation on the static buckling behavior of laminated cylindrical composite shells with embedded SMA wires by experiment [Volume 5, Issue 4, 2018, Pages 551-564]

D

  • Damage Experimental and numerical investigation on semi-cylindrical compositelatticereinforced with triangular cellssubjected to high velocity impact [Volume 5, Issue 2, 2018, Pages 208-217]
  • Damage Three dimensional weft knitted sandwich composites under drop-weight impacts in different energy levels [Volume 5, Issue 2, 2018, Pages 271-278]
  • Date palm fibers Tensile and flexural properties of epoxy-date palm fiber composites [Volume 5, Issue 1, 2018, Pages 69-78]
  • Delamination Statistical study of the effect of various machining parameters on delamination in drilling of carbon fiber reinforced composites [Volume 5, Issue 1, 2018, Pages 41-50]
  • Delamination Buckling analysis of composite cross-ply laminated plates under hygrothermal loads with delaminations using the finite strip method [Volume 5, Issue 3, 2018, Pages 437-450]
  • Delamination Development of a layer-wise model together with J-integral method for prediction of interlaminar crack growth in laminated composites plates [Volume 5, Issue 2, 2018, Pages 218-226]
  • Delamination Improvement of delamination resistance of glass-phenolic composites through matrix toughening mechanism using poly (vinyl butyral) [Volume 5, Issue 4, 2018, Pages 521-528]
  • Drop-weight impact Three dimensional weft knitted sandwich composites under drop-weight impacts in different energy levels [Volume 5, Issue 2, 2018, Pages 271-278]

E

  • Eccentricity Prediction and control of the mechanical properties of braided composite by controlling the braid angle using the micro-mechanical relationships for each of the flat faces of mandrel [Volume 5, Issue 4, 2018, Pages 595-604]
  • Effect of core cross-sectional shape Three dimensional weft knitted sandwich composites under drop-weight impacts in different energy levels [Volume 5, Issue 2, 2018, Pages 271-278]
  • Electrodeposition The comparison in corrosion behavior of Fe-Ni-Cr composite coatings reinforced by SiC nanoparticles and carbon nanotubes [Volume 5, Issue 3, 2018, Pages 369-376]
  • Electro-elastic Micromechanical analysis of electro-elastic response of polymer composites reinforced with fuzzy fiber containing CNTs [Volume 5, Issue 4, 2018, Pages 485-498]
  • Electromechanical coupling Energy Harvesting from Laminated Composite Beam with a Piezoelectric Layer under Forced Vibrations [Volume 5, Issue 2, 2018, Pages 227-237]
  • Electrospinning A Study on morphology of Poly(vinyl alcohol)- organoclay nanocomposite nanofibers [Volume 5, Issue 3, 2018, Pages 325-330]
  • Energy level Three dimensional weft knitted sandwich composites under drop-weight impacts in different energy levels [Volume 5, Issue 2, 2018, Pages 271-278]
  • EPDM Experimental analysis of graphene nanoparticles and glass fibers effect on mechanical and thermal properties of polypropylene/EPDM based nanocomposites [Volume 5, Issue 2, 2018, Pages 169-176]
  • Epoxy/Glass prepreg Effect of CTBN liquid rubber and flexible diamine curing agent on epoxy/glass prepregs properties [Volume 5, Issue 1, 2018, Pages 25-32]
  • Epoxy resin Effect of CTBN liquid rubber and flexible diamine curing agent on epoxy/glass prepregs properties [Volume 5, Issue 1, 2018, Pages 25-32]
  • Expanded graphite Electrical conductivity enhancement of Carbon/Epoxy composites using nanoparticles [Volume 5, Issue 4, 2018, Pages 605-614]
  • Experimental design Investigation of mechanical properties of polypropylene-based hybrid nanocomposites using experimental design [Volume 5, Issue 3, 2018, Pages 307-314]

F

  • Fabrication Prediction of the critical buckling load of composite cylindrical shells by using Vibration Correlation Technique [Volume 5, Issue 3, 2018, Pages 359-368]
  • Fe-B Studying influence of adding carbon and boron amount on microstructure and hardness of iron – based hardfacing layer using Flux Cored Arc Welding [Volume 5, Issue 2, 2018, Pages 245-252]
  • Fiber metal laminate Experimental and numerical investigation of high velocity impact resistance in fiber metal laminates [Volume 5, Issue 1, 2018, Pages 99-108]
  • Fiber metal laminate An Experimental investigation on nitinol shape memory alloy reinforced GLAREs against Charpy low velocity impact [Volume 5, Issue 3, 2018, Pages 403-414]
  • Fiber metal laminates The effect of middle layer material and thickness on the quasi-static energy absorption of FML [Volume 5, Issue 3, 2018, Pages 427-436]
  • Fiber-metal laminates Mechanical performance of self-healing fiber-metal laminates under transverse loading [Volume 5, Issue 2, 2018, Pages 185-190]
  • Fibre reinforced composite Three dimensional modeling of progressive damage in fiber reinforced materials base on invariant failure criteria [Volume 5, Issue 2, 2018, Pages 191-199]
  • Filament winding Experimental and numerical free vibration analysis of composite sandwich cylindrical shells with lozenge cores [Volume 5, Issue 4, 2018, Pages 469-478]
  • Finite element Investigation of skin/core debonding effects on the natural frequencies of composite sandwich structures using experimental and numerical modal analysis [Volume 5, Issue 1, 2018, Pages 91-98]
  • Finite strip method Buckling analysis of composite cross-ply laminated plates under hygrothermal loads with delaminations using the finite strip method [Volume 5, Issue 3, 2018, Pages 437-450]
  • First order shear deformation plate theory Hydroelastic vibration analysis of functionally graded circular plate in contact with bounded fluid by Ritz method [Volume 5, Issue 4, 2018, Pages 529-538]
  • Flexural modulus Evaluation of variation in the mechanical properties of composite laminates using progressive failure analysis [Volume 5, Issue 1, 2018, Pages 51-60]
  • Flexural properties Effects of functionalized graphene nanoplatelets on the flexural behaviors of basalt fibers/epoxy composites [Volume 5, Issue 3, 2018, Pages 315-324]
  • Flexural Strength Evaluation of variation in the mechanical properties of composite laminates using progressive failure analysis [Volume 5, Issue 1, 2018, Pages 51-60]
  • Flexural Strength Mechanical performance of self-healing fiber-metal laminates under transverse loading [Volume 5, Issue 2, 2018, Pages 185-190]
  • Flexural Strength Improvement of delamination resistance of glass-phenolic composites through matrix toughening mechanism using poly (vinyl butyral) [Volume 5, Issue 4, 2018, Pages 521-528]
  • FML Analytical modeling to predict dynamic response of Fiber-Metal Laminated Panel subjected to low velocity impact [Volume 5, Issue 3, 2018, Pages 331-342]
  • Foaming dynamics Experimental Investigation on the Foaming Dynamics and Cell Microstructure of Polystyrene/Nanosilica/n-Pentane Nanocomposites [Volume 5, Issue 2, 2018, Pages 289-301]
  • Forced Vibration Energy Harvesting from Laminated Composite Beam with a Piezoelectric Layer under Forced Vibrations [Volume 5, Issue 2, 2018, Pages 227-237]
  • Free edge Development of a layer-wise model together with J-integral method for prediction of interlaminar crack growth in laminated composites plates [Volume 5, Issue 2, 2018, Pages 218-226]
  • Free vibration Experimental and numerical free vibration analysis of composite sandwich cylindrical shells with lozenge cores [Volume 5, Issue 4, 2018, Pages 469-478]
  • Friction stir processing Fabrication and investigation of microstructutr and mechanical properties of A356-TiO2-Gr surface Hybrid nano composite by friction stir processing [Volume 5, Issue 1, 2018, Pages 61-68]
  • Functionalization Effects of functionalized graphene nanoplatelets on the flexural behaviors of basalt fibers/epoxy composites [Volume 5, Issue 3, 2018, Pages 315-324]
  • Functionally graded material Hydroelastic vibration analysis of functionally graded circular plate in contact with bounded fluid by Ritz method [Volume 5, Issue 4, 2018, Pages 529-538]
  • Functionally graded material cylindrical shells Thermal Stability of FGM Cylindrical Shells on Pasternak Elastic Foundation under Axial Load [Volume 5, Issue 2, 2018, Pages 200-207]
  • Fuzzy clustering Failure mechanisms in open-hole laminated composites under tensile loading using acoustic emission [Volume 5, Issue 1, 2018, Pages 143-152]
  • Fuzzy fiber Micromechanical analysis of electro-elastic response of polymer composites reinforced with fuzzy fiber containing CNTs [Volume 5, Issue 4, 2018, Pages 485-498]

G

  • Gas Gun Experimental and numerical investigation of high velocity impact resistance in fiber metal laminates [Volume 5, Issue 1, 2018, Pages 99-108]
  • GLARE An Experimental investigation on nitinol shape memory alloy reinforced GLAREs against Charpy low velocity impact [Volume 5, Issue 3, 2018, Pages 403-414]
  • Glass fiber Experimental analysis of graphene nanoparticles and glass fibers effect on mechanical and thermal properties of polypropylene/EPDM based nanocomposites [Volume 5, Issue 2, 2018, Pages 169-176]
  • Glass-phenolic Composites Improvement of delamination resistance of glass-phenolic composites through matrix toughening mechanism using poly (vinyl butyral) [Volume 5, Issue 4, 2018, Pages 521-528]
  • Graphene Experimental analysis of graphene nanoparticles and glass fibers effect on mechanical and thermal properties of polypropylene/EPDM based nanocomposites [Volume 5, Issue 2, 2018, Pages 169-176]
  • Graphene Effects of functionalized graphene nanoplatelets on the flexural behaviors of basalt fibers/epoxy composites [Volume 5, Issue 3, 2018, Pages 315-324]
  • Graphene Experimental investigation on mechanical properties of hybrid nano-composite based on epoxy/ graphene nano-platelets/ carboxylated acrylonitrile butadiene rubber [Volume 5, Issue 3, 2018, Pages 395-402]
  • Graphene nanoplatelets Effect of Surface Modification of Graphene Nanoplatelets on the High Velocity Impact Behavior of Basalt Fibers Reinforced Polymer-Based Composites [Volume 5, Issue 1, 2018, Pages 109-116]

H

  • Hardness Fabrication of magnesium sheet with magnesium matrix surface composite to improve hardness and wear properties [Volume 5, Issue 4, 2018, Pages 575-582]
  • Healing efficiency Mechanical performance of self-healing fiber-metal laminates under transverse loading [Volume 5, Issue 2, 2018, Pages 185-190]
  • High density polyethylene Investigation of the physical and mechanical properties of Wood plastic composites based on high density polyethylene/ polypropylene/recycled poly (ethylene terephthalate) [Volume 5, Issue 1, 2018, Pages 127-134]
  • High velocity impact Finite element simulation of high velocity impact on polymer composite plates [Volume 5, Issue 2, 2018, Pages 157-168]
  • High velocity impact Effect of Surface Modification of Graphene Nanoplatelets on the High Velocity Impact Behavior of Basalt Fibers Reinforced Polymer-Based Composites [Volume 5, Issue 1, 2018, Pages 109-116]
  • High velocity impact Numerical investigation of the effect of material strain rate dependent properties on high velocity impact behavior and ballistic limit velocity of honeycomb structures [Volume 5, Issue 4, 2018, Pages 511-520]
  • Honeycomb Experimental and numerical investigation of sandwich panels with bilateral connection under static loading [Volume 5, Issue 3, 2018, Pages 415-426]
  • Honeycomb Numerical investigation of the effect of material strain rate dependent properties on high velocity impact behavior and ballistic limit velocity of honeycomb structures [Volume 5, Issue 4, 2018, Pages 511-520]
  • Hot gas forming Experimental and Finite Element Investigation of Hot Gas Forming Process of A6063-AZ80 Bi-layered Composite Tubes using Taguchi Methods for Design of Experiments [Volume 5, Issue 1, 2018, Pages 79-90]
  • Hot Rolling Fabrication of magnesium sheet with magnesium matrix surface composite to improve hardness and wear properties [Volume 5, Issue 4, 2018, Pages 575-582]
  • Hybrid Finite element simulation of high velocity impact on polymer composite plates [Volume 5, Issue 2, 2018, Pages 157-168]
  • Hydroxyapatite Effect of Nitinol Addition on the Mechanical properties and the Microstructure of Nactural Hydroxyapatite Obtained from Calf Femoral Bone [Volume 5, Issue 2, 2018, Pages 238-244]
  • Hygrothermal loads Buckling analysis of composite cross-ply laminated plates under hygrothermal loads with delaminations using the finite strip method [Volume 5, Issue 3, 2018, Pages 437-450]

I

  • Impact Experimental, numerical and analytical study of energy absorption in high velocity penetration phenomena on composite targets. [Volume 5, Issue 1, 2018, Pages 11-24]
  • Impact strength Investigation of mechanical properties of polypropylene-based hybrid nanocomposites using experimental design [Volume 5, Issue 3, 2018, Pages 307-314]
  • Imperfection Ultimate strength analysis of imperfect composite plates under both in-plane compressive load and lateral pressure using Ritz method [Volume 5, Issue 1, 2018, Pages 1-10]
  • Invariant Three dimensional modeling of progressive damage in fiber reinforced materials base on invariant failure criteria [Volume 5, Issue 2, 2018, Pages 191-199]

J

  • Jeffamine Effect of CTBN liquid rubber and flexible diamine curing agent on epoxy/glass prepregs properties [Volume 5, Issue 1, 2018, Pages 25-32]
  • J-Integral Development of a layer-wise model together with J-integral method for prediction of interlaminar crack growth in laminated composites plates [Volume 5, Issue 2, 2018, Pages 218-226]

L

  • Lateral pressure Ultimate strength analysis of imperfect composite plates under both in-plane compressive load and lateral pressure using Ritz method [Volume 5, Issue 1, 2018, Pages 1-10]
  • Layer-wise theory Development of a layer-wise model together with J-integral method for prediction of interlaminar crack growth in laminated composites plates [Volume 5, Issue 2, 2018, Pages 218-226]
  • Low velocity impact A semi-empirical model to predict the low-velocity impact behavior of weft-knitted spacer fabrics reinforced composites [Volume 5, Issue 1, 2018, Pages 117-126]
  • Low velocity impact Analytical modeling to predict dynamic response of Fiber-Metal Laminated Panel subjected to low velocity impact [Volume 5, Issue 3, 2018, Pages 331-342]
  • Low velocity impact Response of aluminum foam sandwiches under low rate impact [Volume 5, Issue 2, 2018, Pages 177-184]
  • Lozenge core Experimental and numerical free vibration analysis of composite sandwich cylindrical shells with lozenge cores [Volume 5, Issue 4, 2018, Pages 469-478]

M

  • Machining parameters Statistical study of the effect of various machining parameters on delamination in drilling of carbon fiber reinforced composites [Volume 5, Issue 1, 2018, Pages 41-50]
  • Magnesium. Magnesium matrix composite Fabrication of magnesium sheet with magnesium matrix surface composite to improve hardness and wear properties [Volume 5, Issue 4, 2018, Pages 575-582]
  • Mechanical and physical properties Investigation of the physical and mechanical properties of Wood plastic composites based on high density polyethylene/ polypropylene/recycled poly (ethylene terephthalate) [Volume 5, Issue 1, 2018, Pages 127-134]
  • Mechanical properties Experimental analysis of graphene nanoparticles and glass fibers effect on mechanical and thermal properties of polypropylene/EPDM based nanocomposites [Volume 5, Issue 2, 2018, Pages 169-176]
  • Mechanical properties Fabrication and investigation of microstructutr and mechanical properties of A356-TiO2-Gr surface Hybrid nano composite by friction stir processing [Volume 5, Issue 1, 2018, Pages 61-68]
  • Mechanical properties Experimental investigation on mechanical properties of hybrid nano-composite based on epoxy/ graphene nano-platelets/ carboxylated acrylonitrile butadiene rubber [Volume 5, Issue 3, 2018, Pages 395-402]
  • Mechanical properties Effect of Nitinol Addition on the Mechanical properties and the Microstructure of Nactural Hydroxyapatite Obtained from Calf Femoral Bone [Volume 5, Issue 2, 2018, Pages 238-244]
  • Metal Matrix Composite Review of mechanical and microstructural properties of aluminum matrix composites reinforced with ceramic particles produced by SPD processes [Volume 5, Issue 4, 2018, Pages 583-594]
  • Microcellular nanocomposite Investigation of cell wall thickness and impact strength of polypropylene microcellular nanocomposite foams produced by batch process [Volume 5, Issue 1, 2018, Pages 135-142]
  • Micro-cracks Mechanical performance of self-healing fiber-metal laminates under transverse loading [Volume 5, Issue 2, 2018, Pages 185-190]
  • Micromechanical analysis Prediction and control of the mechanical properties of braided composite by controlling the braid angle using the micro-mechanical relationships for each of the flat faces of mandrel [Volume 5, Issue 4, 2018, Pages 595-604]
  • Micromechanics Micromechanical analysis of electro-elastic response of polymer composites reinforced with fuzzy fiber containing CNTs [Volume 5, Issue 4, 2018, Pages 485-498]
  • Microstructure Studying influence of adding carbon and boron amount on microstructure and hardness of iron – based hardfacing layer using Flux Cored Arc Welding [Volume 5, Issue 2, 2018, Pages 245-252]
  • Multi-walled carbon nanotubes Theoretical and experimental study on the effect of multi-walled carbon nanotubes on improving the tensile properties and toughness of Vinyl ester resin [Volume 5, Issue 4, 2018, Pages 539-550]

N

  • Nanocomposite Effect of Surface Modification of Graphene Nanoplatelets on the High Velocity Impact Behavior of Basalt Fibers Reinforced Polymer-Based Composites [Volume 5, Issue 1, 2018, Pages 109-116]
  • Nanocomposite Investigation of mechanical properties of polypropylene-based hybrid nanocomposites using experimental design [Volume 5, Issue 3, 2018, Pages 307-314]
  • Nanocomposite A Study on morphology of Poly(vinyl alcohol)- organoclay nanocomposite nanofibers [Volume 5, Issue 3, 2018, Pages 325-330]
  • Nanocomposite Investigation on the Microstructure and Properties of PVC Toughened with DOP/PMMA/Nano-Graphene [Volume 5, Issue 3, 2018, Pages 451-456]
  • Nanocomposite Curing kinetic of micro and nano composites based on styrenine butadiene rubber contains zinc oxide [Volume 5, Issue 2, 2018, Pages 253-264]
  • Nanocomposites Theoretical and experimental study on the effect of multi-walled carbon nanotubes on improving the tensile properties and toughness of Vinyl ester resin [Volume 5, Issue 4, 2018, Pages 539-550]
  • Nano Fe2O3 Investigation of cell wall thickness and impact strength of polypropylene microcellular nanocomposite foams produced by batch process [Volume 5, Issue 1, 2018, Pages 135-142]
  • Nano fiber A Study on morphology of Poly(vinyl alcohol)- organoclay nanocomposite nanofibers [Volume 5, Issue 3, 2018, Pages 325-330]
  • Nanographene Investigation on the Microstructure and Properties of PVC Toughened with DOP/PMMA/Nano-Graphene [Volume 5, Issue 3, 2018, Pages 451-456]
  • Ni particle Evaluation of mechanical properties and microstructure for Al/Ni %5 produced by cross accumulative roll bonding process [Volume 5, Issue 2, 2018, Pages 279-288]
  • Nitinol An Experimental investigation on nitinol shape memory alloy reinforced GLAREs against Charpy low velocity impact [Volume 5, Issue 3, 2018, Pages 403-414]
  • Nitinol Effect of Nitinol Addition on the Mechanical properties and the Microstructure of Nactural Hydroxyapatite Obtained from Calf Femoral Bone [Volume 5, Issue 2, 2018, Pages 238-244]
  • Nonisothermal Curing kinetic of micro and nano composites based on styrenine butadiene rubber contains zinc oxide [Volume 5, Issue 2, 2018, Pages 253-264]
  • Numerical analysis Prediction of the critical buckling load of composite cylindrical shells by using Vibration Correlation Technique [Volume 5, Issue 3, 2018, Pages 359-368]
  • Numerical Modeling Numerical investigation of the effect of material strain rate dependent properties on high velocity impact behavior and ballistic limit velocity of honeycomb structures [Volume 5, Issue 4, 2018, Pages 511-520]

O

  • Open-cell structure Investigation of cell wall thickness and impact strength of polypropylene microcellular nanocomposite foams produced by batch process [Volume 5, Issue 1, 2018, Pages 135-142]
  • Organo- Clay A Study on morphology of Poly(vinyl alcohol)- organoclay nanocomposite nanofibers [Volume 5, Issue 3, 2018, Pages 325-330]

P

  • Peel strength A Study of layer strength in composite Al 1050/SS 316 manufactured by Accumulative Roll bonding process [Volume 5, Issue 4, 2018, Pages 479-484]
  • Piezoelectric Micromechanical analysis of electro-elastic response of polymer composites reinforced with fuzzy fiber containing CNTs [Volume 5, Issue 4, 2018, Pages 485-498]
  • Piezoelectric Energy Harvesting from Laminated Composite Beam with a Piezoelectric Layer under Forced Vibrations [Volume 5, Issue 2, 2018, Pages 227-237]
  • PMMA Investigation on the Microstructure and Properties of PVC Toughened with DOP/PMMA/Nano-Graphene [Volume 5, Issue 3, 2018, Pages 451-456]
  • Pocket wavelet transform Failure mechanisms in open-hole laminated composites under tensile loading using acoustic emission [Volume 5, Issue 1, 2018, Pages 143-152]
  • Polarization Production of uniform nanocomposite coating of polypyrrole carbon nanotube/ cadmium oxide to protect corrosion of austenitic stainless steel 304 [Volume 5, Issue 3, 2018, Pages 377-386]
  • Polarization Curves Preparation of SiO2/TiO2 ceramic nano composite coating by sol-gel method on carbon steel and study the properties of it against corrosive ion in treated wastewater [Volume 5, Issue 1, 2018, Pages 33-40]
  • Polypropylene Experimental analysis of graphene nanoparticles and glass fibers effect on mechanical and thermal properties of polypropylene/EPDM based nanocomposites [Volume 5, Issue 2, 2018, Pages 169-176]
  • Polypropylene Investigation of the physical and mechanical properties of Wood plastic composites based on high density polyethylene/ polypropylene/recycled poly (ethylene terephthalate) [Volume 5, Issue 1, 2018, Pages 127-134]
  • Polypropylene Investigation of mechanical properties of polypropylene-based hybrid nanocomposites using experimental design [Volume 5, Issue 3, 2018, Pages 307-314]
  • Polypyrrole & morphology Production of uniform nanocomposite coating of polypyrrole carbon nanotube/ cadmium oxide to protect corrosion of austenitic stainless steel 304 [Volume 5, Issue 3, 2018, Pages 377-386]
  • Polystyrene/nanosilica nanocomposites Experimental Investigation on the Foaming Dynamics and Cell Microstructure of Polystyrene/Nanosilica/n-Pentane Nanocomposites [Volume 5, Issue 2, 2018, Pages 289-301]
  • Polyvinyl alcohol A Study on morphology of Poly(vinyl alcohol)- organoclay nanocomposite nanofibers [Volume 5, Issue 3, 2018, Pages 325-330]
  • Polyvinyl Butyral Improvement of delamination resistance of glass-phenolic composites through matrix toughening mechanism using poly (vinyl butyral) [Volume 5, Issue 4, 2018, Pages 521-528]
  • Progressive failure Evaluation of variation in the mechanical properties of composite laminates using progressive failure analysis [Volume 5, Issue 1, 2018, Pages 51-60]
  • Progressive failure Three dimensional modeling of progressive damage in fiber reinforced materials base on invariant failure criteria [Volume 5, Issue 2, 2018, Pages 191-199]

R

  • Recycled poly (ethylene terephthalate) Investigation of the physical and mechanical properties of Wood plastic composites based on high density polyethylene/ polypropylene/recycled poly (ethylene terephthalate) [Volume 5, Issue 1, 2018, Pages 127-134]
  • Ritz Ultimate strength analysis of imperfect composite plates under both in-plane compressive load and lateral pressure using Ritz method [Volume 5, Issue 1, 2018, Pages 1-10]

S

  • Sandwich shell Experimental and numerical free vibration analysis of composite sandwich cylindrical shells with lozenge cores [Volume 5, Issue 4, 2018, Pages 469-478]
  • Scanning electron microscopy Failure mechanisms in open-hole laminated composites under tensile loading using acoustic emission [Volume 5, Issue 1, 2018, Pages 143-152]
  • Self-healing Mechanical performance of self-healing fiber-metal laminates under transverse loading [Volume 5, Issue 2, 2018, Pages 185-190]
  • Semi-empirical model A semi-empirical model to predict the low-velocity impact behavior of weft-knitted spacer fabrics reinforced composites [Volume 5, Issue 1, 2018, Pages 117-126]
  • Shape memory alloy An Experimental investigation on nitinol shape memory alloy reinforced GLAREs against Charpy low velocity impact [Volume 5, Issue 3, 2018, Pages 403-414]
  • Shape Memory Alloys An investigation on the static buckling behavior of laminated cylindrical composite shells with embedded SMA wires by experiment [Volume 5, Issue 4, 2018, Pages 551-564]
  • Shear strength Effect of CTBN liquid rubber and flexible diamine curing agent on epoxy/glass prepregs properties [Volume 5, Issue 1, 2018, Pages 25-32]
  • Shear strength The Effects of Temperature Level and Stress-to-Strength Ratio on Creep Behavior of Aluminum-Aluminum Single Lap Adhesive Joints [Volume 5, Issue 3, 2018, Pages 353-358]
  • Shear strength A Study of layer strength in composite Al 1050/SS 316 manufactured by Accumulative Roll bonding process [Volume 5, Issue 4, 2018, Pages 479-484]
  • SiC nanoparticles Investigation of the microstructure and hardness of cast Al7068 nanocomposite reinforced with SiC nanoparticles [Volume 5, Issue 4, 2018, Pages 461-468]
  • Silica Nanoparticles Effects of size and structure of silica nanoparticles on morphology and tensile behavior of flexible nanocomposite foams based on polyurethane [Volume 5, Issue 4, 2018, Pages 615-620]
  • Single Lap Joint The Effects of Temperature Level and Stress-to-Strength Ratio on Creep Behavior of Aluminum-Aluminum Single Lap Adhesive Joints [Volume 5, Issue 3, 2018, Pages 353-358]
  • Sintering Compression and impact strength study of aluminum-alumina granule composite by squeez-casting method [Volume 5, Issue 3, 2018, Pages 387-394]
  • Sol-gel Preparation of SiO2/TiO2 ceramic nano composite coating by sol-gel method on carbon steel and study the properties of it against corrosive ion in treated wastewater [Volume 5, Issue 1, 2018, Pages 33-40]
  • SPD Evaluation of mechanical properties and microstructure for Al/Ni %5 produced by cross accumulative roll bonding process [Volume 5, Issue 2, 2018, Pages 279-288]
  • Specific Perforation Energy Experimental and numerical investigation of high velocity impact resistance in fiber metal laminates [Volume 5, Issue 1, 2018, Pages 99-108]
  • Static Buckling An investigation on the static buckling behavior of laminated cylindrical composite shells with embedded SMA wires by experiment [Volume 5, Issue 4, 2018, Pages 551-564]
  • Stir casting Investigation of the microstructure and hardness of cast Al7068 nanocomposite reinforced with SiC nanoparticles [Volume 5, Issue 4, 2018, Pages 461-468]
  • Strain energy release rate Development of a layer-wise model together with J-integral method for prediction of interlaminar crack growth in laminated composites plates [Volume 5, Issue 2, 2018, Pages 218-226]
  • Strain Rate Dependent Properties Numerical investigation of the effect of material strain rate dependent properties on high velocity impact behavior and ballistic limit velocity of honeycomb structures [Volume 5, Issue 4, 2018, Pages 511-520]
  • Structural health monitoring Utilization of artificial neural networks for detection and classification of damages in composite plate-like structures via ultrasonic guided waves [Volume 5, Issue 3, 2018, Pages 343-352]
  • Superelastic An investigation on the static buckling behavior of laminated cylindrical composite shells with embedded SMA wires by experiment [Volume 5, Issue 4, 2018, Pages 551-564]
  • Surface composite Fabrication of magnesium sheet with magnesium matrix surface composite to improve hardness and wear properties [Volume 5, Issue 4, 2018, Pages 575-582]
  • Surface modification Effect of Surface Modification of Graphene Nanoplatelets on the High Velocity Impact Behavior of Basalt Fibers Reinforced Polymer-Based Composites [Volume 5, Issue 1, 2018, Pages 109-116]
  • Surface nano composites Fabrication and investigation of microstructutr and mechanical properties of A356-TiO2-Gr surface Hybrid nano composite by friction stir processing [Volume 5, Issue 1, 2018, Pages 61-68]

T

  • Taguchi method Experimental and Finite Element Investigation of Hot Gas Forming Process of A6063-AZ80 Bi-layered Composite Tubes using Taguchi Methods for Design of Experiments [Volume 5, Issue 1, 2018, Pages 79-90]
  • Taguchi method Experimental and numerical free vibration analysis of composite sandwich cylindrical shells with lozenge cores [Volume 5, Issue 4, 2018, Pages 469-478]
  • Tensile behavior Effects of size and structure of silica nanoparticles on morphology and tensile behavior of flexible nanocomposite foams based on polyurethane [Volume 5, Issue 4, 2018, Pages 615-620]
  • Tensile strength Theoretical and experimental study on the effect of multi-walled carbon nanotubes on improving the tensile properties and toughness of Vinyl ester resin [Volume 5, Issue 4, 2018, Pages 539-550]
  • Tension Tensile and flexural properties of epoxy-date palm fiber composites [Volume 5, Issue 1, 2018, Pages 69-78]
  • Total potential energy Analytical modeling to predict dynamic response of Fiber-Metal Laminated Panel subjected to low velocity impact [Volume 5, Issue 3, 2018, Pages 331-342]
  • Toughening Improvement of delamination resistance of glass-phenolic composites through matrix toughening mechanism using poly (vinyl butyral) [Volume 5, Issue 4, 2018, Pages 521-528]
  • Toughness Theoretical and experimental study on the effect of multi-walled carbon nanotubes on improving the tensile properties and toughness of Vinyl ester resin [Volume 5, Issue 4, 2018, Pages 539-550]
  • Trapezoidal Compound core Experimental and numerical study of Energy Absorption in foam filled Trapezoidal Compound core sandwich panels subjected to quasi-static loading. [Volume 5, Issue 4, 2018, Pages 565-574]

U

  • Ultimate Strength Ultimate strength analysis of imperfect composite plates under both in-plane compressive load and lateral pressure using Ritz method [Volume 5, Issue 1, 2018, Pages 1-10]
  • Ultrasonic guided waves Utilization of artificial neural networks for detection and classification of damages in composite plate-like structures via ultrasonic guided waves [Volume 5, Issue 3, 2018, Pages 343-352]
  • Ultrasonic treatment Investigation of the microstructure and hardness of cast Al7068 nanocomposite reinforced with SiC nanoparticles [Volume 5, Issue 4, 2018, Pages 461-468]
  • UPVC Investigation on the Microstructure and Properties of PVC Toughened with DOP/PMMA/Nano-Graphene [Volume 5, Issue 3, 2018, Pages 451-456]

V

  • Vibration correlation technique Prediction of the critical buckling load of composite cylindrical shells by using Vibration Correlation Technique [Volume 5, Issue 3, 2018, Pages 359-368]
  • Vulcanization Curing kinetic of micro and nano composites based on styrenine butadiene rubber contains zinc oxide [Volume 5, Issue 2, 2018, Pages 253-264]

W

  • Wavelet transform Utilization of artificial neural networks for detection and classification of damages in composite plate-like structures via ultrasonic guided waves [Volume 5, Issue 3, 2018, Pages 343-352]
  • Wear Fabrication and investigation of microstructutr and mechanical properties of A356-TiO2-Gr surface Hybrid nano composite by friction stir processing [Volume 5, Issue 1, 2018, Pages 61-68]
  • Wear test Fabrication of magnesium sheet with magnesium matrix surface composite to improve hardness and wear properties [Volume 5, Issue 4, 2018, Pages 575-582]
  • Wood-plastic Investigation of the physical and mechanical properties of Wood plastic composites based on high density polyethylene/ polypropylene/recycled poly (ethylene terephthalate) [Volume 5, Issue 1, 2018, Pages 127-134]
  • Workpiece thickness Statistical study of the effect of various machining parameters on delamination in drilling of carbon fiber reinforced composites [Volume 5, Issue 1, 2018, Pages 41-50]
  • Woven carbon composite Numerical investigation of tensile behavior of composite reinforced with woven carbon and Kevlar fabrics by multi scale method [Volume 5, Issue 2, 2018, Pages 265-270]

X

  • XNBR Experimental investigation on mechanical properties of hybrid nano-composite based on epoxy/ graphene nano-platelets/ carboxylated acrylonitrile butadiene rubber [Volume 5, Issue 3, 2018, Pages 395-402]

Y

  • Young's modulus Theoretical and experimental study on the effect of multi-walled carbon nanotubes on improving the tensile properties and toughness of Vinyl ester resin [Volume 5, Issue 4, 2018, Pages 539-550]

Z

  • Zinc oxide Curing kinetic of micro and nano composites based on styrenine butadiene rubber contains zinc oxide [Volume 5, Issue 2, 2018, Pages 253-264]